Advertisements
[AdSlot: TOP-1 • Reserved Container • CLS-Safe]

New Furnace and AC Unit Cost: Complete HVAC Replacement Price Guide

Direct Answer: A furnace that is not working usually stems from five common issues: a tripped circuit breaker, an emergency shutoff switch flipped off, a clogged furnace filter triggering high-limit switches, incorrect thermostat settings, or an electronic igniter failure. Check external switches, mode settings, and filter airflow before scheduling an emergency service call.

Advertisements
[AdSlot: ART-1 • Reserved Container • CLS-Safe]
Table of Contents

A new furnace and AC unit cost typically ranges from $5,000 to $12,500 installed for a complete matched residential system, averaging $7,500 nationally according to 2026 project data from Angi. When purchasing equipment separately, an individual replacement furnace costs $2,800 to $6,900 while a new central air conditioner runs $3,900 to $8,000 per Angi’s bundled replacement guide.

Complementary national pricing data from HomeGuide confirms that pairing a central air conditioner with a furnace typically costs $5,000 to $11,000 for a complete system.

When replacing only the heating unit, standalone furnace replacement averages $3,500 to $7,500 for standard models (up to $11,500 for high efficiency) per HomeGuide furnace replacement data.

Replacing your furnace and air conditioner at the same time is one of the largest capital investments you will make as a homeowner. Understanding the major price drivers, regional labor variances, and equipment efficiency standards helps you secure a fair estimate and avoid paying thousands of dollars in unnecessary dealer markups.

How Much Does a New Furnace and AC Unit Cost?

Total installed pricing for a complete heating and cooling system combines two separate mechanical units: the indoor heating plant (a gas, electric, or oil furnace) and the outdoor split-system cooling unit (the central air conditioner condenser and indoor evaporator coil).

Because licensed contractors must pull local building permits, decommission and dispose of existing equipment, modify sheet metal plenum transitions, run new refrigeration line sets, and wire low-voltage controls, installation labor represents a substantial share of the total invoice cost.

  • Standard straight changeout (existing ductwork retained) - Swapping your existing central AC and furnace for more efficient models typically costs $3,300 to $16,000 fully installed according to Angi’s HVAC price guide.
  • Complete paired furnace and AC system - Complete paired systems average $7,500 with most projects ranging between $5,000 and $12,500 according to Angi’s HVAC price guide.
  • Comprehensive full installation with new ductwork - Extensive whole-home retrofits including custom ductwork typically range from $8,500 to $19,200 according to Angi’s HVAC price guide.

Next in this series: Before signing an HVAC equipment proposal, discover the exact timeline, permits, and startup checklist in our step-by-step guide to furnace installation.

What Drives the Price of a Full HVAC System?

HVAC quotes for the identical floor plan can vary by several thousand dollars between contractors. This spread results from equipment specifications, home construction characteristics, and regional labor rates.

  1. Equipment Capacity and Tonnage: Residential cooling systems are sized in tons (where 1 ton equals 12,000 BTUs of cooling capacity per the U.S. Department of Energy), while furnaces are measured in total heating BTUs per hour. Sizing must be calculated using the Air Conditioning Contractors of America (ACCA) Manual J load calculation standard rather than square footage guessing. Larger higher-tonnage systems require heavier electrical wiring, bigger coils, and larger duct transitions than smaller units, raising total equipment and installation costs.

  2. Energy Efficiency Ratings (SEER2 and AFUE): Equipment efficiency is guided by standards from the U.S. Department of Energy, which updated national testing metrics to SEER2 and HSPF2. Higher efficiency air conditioners and higher Annual Fuel Utilization Efficiency (AFUE) furnaces incorporate advanced multi-stage compressors, secondary stainless steel condensing heat exchangers, and electronically commutated blower motors (ECM).

  3. Existing Ductwork Condition and Sizing: If your existing supply and return trunk ducts are undersized, rusted, or leaking, installing a high-airflow modern system will cause high static pressure, noisy registers, and premature blower motor burnout. Repairing, sealing, or modifying ductwork adds substantial labor and material expense to your replacement invoice (with full ductwork installation adding around $3,500 per Angi).

  4. Flue Venting and Condensate Drainage Modifications: Upgrading from a standard-efficiency natural draft furnace to a high-efficiency condensing furnace (rated 90% AFUE in southern climates and 95% AFUE in northern climates for ENERGY STAR gas models per the U.S. Department of Energy) requires running dedicated plastic intake and exhaust pipes, condensate traps, and drain routing.

How Do Furnace + AC, Heat Pump and Dual Fuel Systems Compare on Cost?

When modernizing a whole-home heating and cooling setup, homeowners are no longer restricted to traditional gas furnace and central AC split configurations. Modern electric heat pumps and hybrid dual-fuel systems offer viable alternatives with distinct cost and operating profiles.

System Type / Architecture Equipment Included in Package Typical Installed Cost Range Best Suited Climate / Region
Natural Gas Furnace + Central AC Gas furnace, AC condenser, cased evaporator coil $5,000 - $12,500 per Angi Regions with established natural gas lines & cold winters
All-Electric Air-Source Heat Pump Heat pump condenser, indoor air handler, aux heat strips $4,500 - $8,000 per Angi Southern, Mid-Atlantic, & Pacific Northwest climates
Dual-Fuel Hybrid System Gas furnace + high-efficiency heat pump $2,500 - $10,000 per Angi Cold northern zones wanting gas backup during extreme cold snaps
Ductless Multi-Zone Mini Split Multi-port outdoor condenser + indoor wall heads $2,000 - $14,500 per Angi Older homes without existing sheet-metal ductwork

An all-electric air-source heat pump handles both heating and cooling through a single outdoor unit and indoor air handler. According to NEEP cold-climate product listings and ENERGY STAR guidance, qualified cold-climate heat pumps are rated for heating capacity even at 5°F outdoor temperatures.

However, in areas where winter temperatures routinely plunge below freezing, a dual-fuel hybrid system pairs an electric heat pump with an auxiliary gas furnace. The heat pump heats efficiently during mild winter weather, and the furnace ignites automatically when extreme arctic cold arrives.

How Does Home Size Change the System Price?

Square footage provides an initial baseline for system capacity, although insulation levels, window exposure, ceiling heights, and local climate zones dictate final equipment sizing.

The table below reflects average turn-key installation costs (including equipment, basic duct adapters, line sets, standard digital thermostat, and labor) based on data compiled from national contractor reporting across the United States.

Home Finished Square Footage Typical Equipment Capacity Replacement Furnace Cost Range Primary Application Fit
1,000 - 1,500 sq ft Light-load single-story capacity $2,000 - $4,500 per HomeGuide Small ranch homes, cottages, and townhomes
1,500 - 2,500 sq ft Mid-range residential capacity $3,000 - $6,500 per HomeGuide Standard multi-bedroom single-family residences
2,500 - 3,500 sq ft High-capacity multi-level load $4,000 - $9,500 per HomeGuide Large two-story family homes
3,500+ sq ft Maximum residential or dual systems $5,500 - $10,000+ per HomeGuide Expansive homes requiring zoned capacity

Pricing data verified: 2026 national benchmarks compiled from HomeGuide and Angi.

Which Extra Costs Show Up in an HVAC Quote?

When reading contractor proposals, look closely at line items beyond the primary equipment model numbers. Necessary ancillary work often adds to the bottom line:

  • Local Municipal Permits and Code Inspections - HVAC permits typically cost $250 to $400 according to Angi.
  • Ductwork Modifications and Additions - Adding or altering HVAC ductwork averages $3,500 according to Angi.
  • New Thermostat Installation - Installing a new thermostat typically costs $120 to $260 according to Angi.
  • Adding Zoning Controls - Adding multi-zone dampers and controllers costs between $2,000 and $3,000 per Angi.

How Can You Tell if an HVAC Quote Is Fair?

To protect your investment and avoid predatory sales practices, insist on complete transparency from every bidding contractor. A professional HVAC contractor will never give you a binding price over the telephone without inspecting your home’s ductwork, electrical service, and mechanical room layout.

Use this evaluation checklist to assess prospective contractors:

  • Manual J Load Calculation Performed - The estimator must perform a room-by-room heating and cooling calculation. If a salesperson matches the replacement system solely to your old unit’s label without measuring windows or insulation, find another contractor.
  • AHRI Certificate Provided - Ensure the proposal lists the AHRI Directory Certified Reference Number confirming the furnace, indoor coil, and outdoor condenser are engineered and tested as a matched performance system.
  • Detailed Warranty Terms Specified - A reputable proposal outlines both the manufacturer equipment parts warranty and the installing dealer’s labor warranty.
  • Itemized Scope of Work - The estimate must explicitly detail equipment haul-away fees, permit costs, filter rack style, sheet metal duct transitions, and vibration isolation pads.
  • Federal Tax Credits and Utility Rebates - The federal Section 25C credit covered only equipment placed in service before December 31, 2025, per the IRS Energy Efficient Home Improvement Credit page, so a system installed now does not qualify. Check your electric or gas utility and your state energy office for current rebates before you sign a quote.

When Should You Replace Both Units at the Same Time?

Homeowners often ask whether they can replace only the broken furnace during winter, or only the failing air conditioner during summer. While technically possible in split systems, replacing both units together is almost always the smarter long-term strategy for four compelling reasons:

First, replacing both units together saves substantial labor and equipment costs compared to separate purchases—where an individual furnace averages $4,800 and a standalone AC averages $3,900 to $8,000, bundling both averages $7,500 according to Angi. When a contractor is already on site pulling permits, evacuating refrigerant, modifying duct plenums, and wiring controls, performing both installations simultaneously cuts total labor hours nearly in half.

Second, modern cooling efficiency depends on matched components. Pairing a brand-new high-efficiency air conditioner with an aging furnace—especially one over 15 years old per ENERGY STAR—with a sluggish legacy blower fan prevents the air conditioner from achieving its rated cooling output and seasonal efficiency.

Third, legacy refrigerants make mixed replacements problematic. Older air conditioning systems often contain ozone-depleting substances regulated under Clean Air Act Section 608 by the U.S. Environmental Protection Agency, making service and parts increasingly scarce.

Finally, starting fresh with a matched heating and cooling system resets your warranty clock, giving you unified parts coverage across both systems, synchronized maintenance routines, and balanced indoor airflow year-round.

If your heating system is already experiencing ignition failures or erratic operation, review our comprehensive furnace troubleshooting guide to determine whether an immediate repair or full system replacement makes the best financial sense.

Frequently Asked Questions

Can I replace my AC unit and keep my old furnace?

Yes, you can replace only the AC condenser and evaporator coil while keeping an existing furnace. However, if your furnace is over 15 years old per ENERGY STAR replacement guidelines, its older single-speed blower motor can bottleneck your new AC unit’s efficiency. You will also forfeit shared installation labor discounts and risk paying for another costly installation just a few years later.

How long does a full furnace and AC installation take?

A standard residential furnace and air conditioner replacement is typically completed in a single full working day by a crew of certified technicians. Complex retrofits requiring duct modifications, secondary flue gas venting, or electrical panel upgrades may extend into a second day.

What is the most reliable brand of furnace and air conditioner?

Top-tier HVAC manufacturers including Trane, American Standard, Carrier, Bryant, Lennox, Rheem, and Goodman build highly reliable systems. However, industry data shows that installation quality matters far more than brand badge. A properly sized and meticulously installed mid-range unit will consistently outlast and outperform a poorly installed premium system.

How much can I save on my electric bill with a high-efficiency system?

Switching to high-efficiency air conditioners and taking efficiency actions can reduce air conditioning energy use by 20% to 50% according to the U.S. Department of Energy, while upgrading from a SEER 10 air conditioner to a SEER 15 system can cut a $100 monthly cooling bill by up to $35 per DOE guidance. Actual savings depend on your local electric and gas utility rates.

Ready to Get Your HVAC Quotes Evaluated?

Upgrading your home’s heating and cooling system represents an essential investment in year-round family comfort, indoor air quality, and property resale value. Armed with realistic cost benchmarks and verified sizing principles, you can navigate contractor proposals with confidence.

Explore our full library of equipment guides on our HVAC costs hub or learn how to maintain your current equipment with our air conditioner maintenance checklist.

Advertisements
[AdSlot: ART-2 • Reserved Container • CLS-Safe]
Safety Warning: High voltage electrical wiring, gas lines, and pressurized refrigerant lines present severe shock, fire, explosion, or toxic gas hazards. Always shut off power at the main breaker before inspecting components. Refrigerant handling requires federal EPA certification. Gas valve and heat exchanger repairs must be performed by a licensed professional technician.
Advertisements
[AdSlot: END-1 • Reserved Container • CLS-Safe]

ComfortBench Editorial Team

HVAC Research & Editorial Staff

The ComfortBench Editorial Team researches, develops, and fact-checks practical HVAC replacement cost benchmarks and safe homeowner troubleshooting guides.

Technically reviewed by a licensed HVAC professional on 2026-11-21

Advertisements
[AdSlot: MPX-1 • Reserved Container • CLS-Safe]